IBM 4232 Model 302 Скачать руководство пользователя страница 203

Страница: 203 / 274

Status Codes

Continuous Forms Device (F1) and Dual Purpose Forms Device
(F2):

1. Press Stop.
2. Load forms.

3. Be sure that the forms are loaded correctly and that they are

under the blue forms guide/forms sensor.

4. Be sure that nothing blocks the blue forms guide/forms

sensor.

5. Reset the top of form position.

6. Press Start.

Document Insertion Device (F3) and Auto Sheet Feeder Device
(F4):

1. Press Stop.
2. Press Load/Eject.

3. Load the correct form size, or
4. Check the maximum page length setting and correct it; then

reload the form and restart the print job (see “Introducing the
4232 Printer Model 302” in

IBM 4232 Printer Model 302 Product

and Programming Description for more information on the
maximum page length setting).

ðð1 END OF FORMS

LOAD FORMS

Appendix B. Problems

B-3

Содержание 4232 Model 302



















































































































































































































































































Результаты поиска

Содержание 4232 Model 302

Отзывы:

Бренды по названию

Популярные бренды

IBM 4232 Model 302, Руководство пользователя

Результаты поиска

Содержание 4232 Model 302

Отзывы:

Бренды по названию

Популярные бренды