IBM 4232 Model 302 страница 179 Скачать руководство пользователя

Страница: 179 / 274

The printer then displays

4. If the

H’s do not print where you want your top of form position,

you can adjust the setting with the following keys:

Line Feed Advance form 4.23 mm (0.17 in.)
Micro

↑

Advance form 0.35 mm (0.0139 in.)

Micro

↓

Move form backward 0.35 mm (0.0139 in.).

5. After you have made an adjustment, press Enter to print the

H’s

again on the same page, or press Form Feed (Load/Eject for
the F3 or F4 forms devices) and then Enter to print the

H’s at

the new top of form position on the next page.

6. Repeat Steps 4 and 5 until the top of form position is where you

want it.

7. Press Set Top of Form to set the new top of form position. The

alarm beeps and the printer displays

8. Press Cancel Print to exit the test and make the printer

ready.

Press Stop to exit the test and return to the Test Menu (see
“General Test Instructions” on page 4-1).

Note: The top of form position can be adjusted without printing the
row of

H’s. See the appropriate section for your forms device on

setting the top of form position.

Top of Form Alignment
Press ENTER to Reprint

TOP OF FORM SET

Chapter 4. Tests

4-5

Содержание 4232 Model 302



















































































































































































































































































Результаты поиска

Содержание 4232 Model 302

Отзывы:

Похожие инструкции для 4232 Model 302

Бренды по названию

Популярные бренды

IBM 4232 Model 302, Руководство пользователя

Результаты поиска

Содержание 4232 Model 302

Отзывы:

Похожие инструкции для 4232 Model 302

Бренды по названию

Популярные бренды