IBM 4232 Model 302 Скачать руководство пользователя | Manualshive

Страница: 15 / 274

background image

Safety Information

The construction of this machine provides extra protection against
the risk of electric shock by grounding appropriate metal parts. The
extra protection may not function unless the power cord is connected
to a properly grounded outlet. This machine has a grounding-type
(3-wire) power cord because grounding is necessary. It is the
responsibility of the customer or the person installing the machine to
connect it to a properly grounded outlet. Seek professional
assistance before using an adapter or extension cord; such a device
could interrupt the grounding circuit.

If this machine is connected to an outlet that has been
incorrectly connected to the building wiring, serious electric
shock could result.

For continued protection against the risk of electric shock and
personal injury:

Connect the machine only to a properly grounded outlet of the
correct voltage. The voltage your machine will accept is
indicated on the machine.

Make sure the machine is turned Off (O) before you connect or
disconnect the power cord or other cables.

If the machine has cables other than the power cord, you must
connect them before you plug the power cord into an outlet. You
must first unplug the power cord from the outlet when you
remove the other cables.

Do not use the machine in an area where it can become wet.

Keep hair and personal articles away from moving parts in the
machine to avoid the possibility of getting them caught.

Refer service or repairs to qualified personnel.

There may be some increased risks of electric shock and
personal injury during disassembly and servicing of this machine.
Professional service personnel should understand this and take
necessary precautions.



Copyright IBM Corp. 1993, 1994

xiii

«
...
13
14
15
16
17
...
»

Содержание 4232 Model 302



















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 4232 Model 302

COLOR SYSTEM 110

Бренд: Oce Страницы: 392

WorkCentre 7655

Бренд: Xerox Страницы: 24

Бренд: Oce Страницы: 90

Бренд: Xante Страницы: 31

Бренд: Edimax Страницы: 93

Бренд: Katun Страницы: 2

Бренд: Xerox Страницы: 150

Magicolor 4650DN

Бренд: Konica Minolta Страницы: 260

Бренд: OKIDATA Страницы: 44

Бренд: idp Страницы: 63

Бренд: Lexmark Страницы: 2

Бренд: Oki Страницы: 105

Stylus Photo 890

Бренд: Epson Страницы: 2

Stylus Photo PX720WD

Бренд: Epson Страницы: 108

Stylus Photo 890

Бренд: Epson Страницы: 1

Stylus Photo Printer PX800FW

Бренд: Epson Страницы: 116

Stylus Office BX925FWD

Бренд: Epson Страницы: 148

Stylus Photo 890

Бренд: Epson Страницы: 241

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды