IBM 4232 Model 302 страница 60 Скачать руководство пользователя | Manualshive

Страница: 60 / 274

background image

Adjusting the Forms Thickness Setting
To adjust the lightness or darkness of the print, you must increase or
decrease the gap between the print head and the platen rod. This
distance is automatically set for you by the Automatic Forms
Thickness Adjustment (AFTA), but you can make corrections to the
distance if the print output is not as you desire. It is up to you to
decide if the print is dark (or light) enough to meet your
requirements.

To adjust the forms thickness setting with the F1 forms device, follow
these steps:

1. The forms thickness setting must be adjusted when the printer is

printing or has printed and is

ready. Press Start, if needed, to

have the printer display

2. To make the print darker, press Darker.

The printer displays

The print head moves closer to the paper, and the print becomes
darker.

Note: The print may not get darker if the ribbon is worn or if
there is a problem with the print head.

3. To make the print lighter, press Lighter.

The printer displays

The print head moves farther away from the paper, and the print
becomes lighter.

READY

<A>

LIGHT |wwwwwwwwwwww-------| DARK

LIGHT |wwwwwwww-----------| DARK

1-38

User’s Guide Model 302

«
...
58
59
60
61
62
...
»

Содержание 4232 Model 302



















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 4232 Model 302

Бренд: IBM Страницы: 112

Бренд: Oki Страницы: 16

Бренд: Labelmate Страницы: 2

Бренд: Tally Страницы: 202

VarioPrint 6000 MICR series

Бренд: Oce Страницы: 264

Бренд: Oce Страницы: 194

Бренд: Oki Страницы: 207

Бренд: Oki Страницы: 56

Бренд: Oki Страницы: 6

Бренд: Oki Страницы: 8

Бренд: Oki Страницы: 16

Бренд: Oki Страницы: 323

Бренд: Oki Страницы: 36

Бренд: Oki Страницы: 150

Бренд: Oki Страницы: 341

Бренд: Oki Страницы: 177

Бренд: Oki Страницы: 162

Бренд: Oki Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды