IBM 4232 Model 302 Скачать руководство пользователя страница 164

Страница: 164 / 274

Starting a Print Job

To start a print job, follow this checklist:

1. Be sure a ribbon cartridge is installed (see “Installing the

Ribbon Cartridge and Guide” on page 1-6 or Chapter 3,
“Replacing Your Ribbon”).

2. Be sure the desired forms device is installed.

See “Installing and Using the Continuous Forms Device
(F1)” on page 1-18, or

See “Installing and Using the Dual Purpose Forms
Device (F2)” on page 1-53, or

See “Installing and Using the Document Insertion Device
(F3)” on page 1-85, or

See “Setting Up Your 4232 Printer with ASF” in

IBM

4232 Printer Model 302 Auto Sheet Feeder General
Information for information on using the Auto Sheet
Feeder.

3. Be sure that the parameter values agree with the application

you are to print.

See the procedures for setting your parameter values in

IBM

4232 Printer Model 302 Operator Panel Instructions.

4. Load forms.

When you load forms, be sure that you use the correct forms
loading procedure and do all of the following:

a. Set the correct forms device setting.

b. Set the top of form position.

c. Adjust the left margin (if needed).

d. Adjust the forms tension (Continuous Forms Device [F1]

only).

5. Verify that the computer is ready to send information to the

printer.

2-22

User’s Guide Model 302

Содержание 4232 Model 302



















































































































































































































































































Результаты поиска

Содержание 4232 Model 302

Отзывы:

Бренды по названию

Популярные бренды

IBM 4232 Model 302, Руководство пользователя

Результаты поиска

Содержание 4232 Model 302

Отзывы:

Бренды по названию

Популярные бренды