IBM 4232 Model 302 страница 100 Скачать руководство пользователя | Manualshive

Страница: 100 / 274

background image

Adjusting the Load Position
The load position can only be adjusted following an operator initiated
load or eject (F2 forms device only) function from the operator panel.

You can adjust the load position using the Micro

↑

, Micro

↓

, or Line

Feed keys. The limits for the position adjustment from the default
position are

+

38 and

−

30.5 mm (

+

1.5 and

−

1.2 in.). If you plan to

use the Document on Demand feature (F2), see “Adjusting the
Tear-off Position” on page 1-76.

Note: Press Set Top of Form to keep the load position consistent
with the top of form position. Pressing Set Top of Form establishes
the first print line at which printing is to start on each form. The
alarm beeps and the printer displays

TOP OF FORM SET

Adjusting the Print Alignment
You can adjust dot registration and print quality for characters
created using bidirectional printing. The bidirectional alignment may
need periodic adjustment to maintain print quality.

To change the bidirectional alignment, follow these steps:

1. If the printer is

ready, press Stop.

The printer displays

2. Press Test.

The printer displays

NOT READY

<A>

OPERATOR PRINT TESTS
Printer Demonstration

1-78

User’s Guide Model 302

«
...
98
99
100
101
102
...
»

Содержание 4232 Model 302



















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 4232 Model 302

Бренд: CAB Страницы: 263

DocuPrint C525 A

Бренд: Xerox Страницы: 49

DocuPrint C2100

Бренд: Xerox Страницы: 206

Бренд: Xerox Страницы: 116

Бренд: Xerox Страницы: 358

Бренд: Xerox Страницы: 344

Бренд: Xerox Страницы: 59

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 10

Бренд: Xerox Страницы: 51

Бренд: Xerox Страницы: 110

7300DX - Phaser Color Laser Printer

Бренд: Xerox Страницы: 8

Бренд: Xerox Страницы: 220

Бренд: Xerox Страницы: 28

8400B - Phaser Color Solid Ink Printer

Бренд: Xerox Страницы: 203

3150 - Phaser B/W Laser Printer

Бренд: Xerox Страницы: 2

3117 - Phaser B/W Laser Printer

Бренд: Xerox Страницы: 8

C8 - DocuPrint Color Inkjet Printer

Бренд: Xerox Страницы: 148

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды