IBM 4232 Model 302 страница 153 Скачать руководство пользователя

Страница: 153 / 274

Power Indicator
The Power indicator has two operating conditions:

The printer is receiving power.

Off

The printer is not receiving power.

Ready Indicator
The Ready indicator has two operating conditions:

The printer is

ready to print.

Off

The printer is

not ready to print.

Processing Indicator
The Processing indicator has three operating conditions:

The printer is currently processing data.

Off

There is no data to be processed and no data is buffered
in the printer.

Blinking

The printer has data buffered, but it cannot currently be
printed.

Online Indicator
The Online indicator has two operating conditions:

The printer is communicating with the computer.

Off

The printer is not communicating with the computer.

Attention Indicator
The Attention indicator has two operating conditions:

Off

The printer has not detected any conditions requiring
operator intervention.

Blinking

The printer has detected a condition requiring immediate
operator intervention. The alarm also beeps (if not
disabled). If the printer also displays a status code, go to
“Using the Status Code and Problem Listings” on
page B-2.

Chapter 2. Getting to Know Your Printer

2-11

Содержание 4232 Model 302



















































































































































































































































































Результаты поиска

Содержание 4232 Model 302

Отзывы:

Похожие инструкции для 4232 Model 302

Бренды по названию

Популярные бренды

IBM 4232 Model 302, Руководство пользователя

Результаты поиска

Содержание 4232 Model 302

Отзывы:

Похожие инструкции для 4232 Model 302

Бренды по названию

Популярные бренды