IBM 4232 Model 302 страница 262 Скачать руководство пользователя

Страница: 262 / 274

serial interface. An interface
where data is exchanged between
the computer and the printer one bit
at a time.

slotted opening. A space on the
bottom of the ribbon cartridge used
to align the cartridge with the metal
post on the printer frame.

SPA. Serial/Parallel Attachment

tear bar. A bar that has an edge
used to separate continuous forms
after they have printed.

tear off position. The location on
continuous forms where they can be

separated using the tear bar on the
F2 forms device.

top of form. A horizontal print line,
near the top of the paper, above
which the printer will not print.

tractor. The mechanism that
controls movement of continuous
forms paper by using the paper
holes in the margins.

tractor doors. Blue doors used to
hold continuous forms against the
tractor pins.

tractor pins. Used to move
continuous forms up or down.

X-6

User’s Guide Model 302

Содержание 4232 Model 302



















































































































































































































































































Результаты поиска

Содержание 4232 Model 302

Отзывы:

Похожие инструкции для 4232 Model 302

Бренды по названию

Популярные бренды

IBM 4232 Model 302, Руководство пользователя

Результаты поиска

Содержание 4232 Model 302

Отзывы:

Похожие инструкции для 4232 Model 302

Бренды по названию

Популярные бренды