Hyundai HL630VL страница 47 Скачать руководство пользователя | Manualshive

Страница: 47 / 161

background image

1-38 Safety

SHIPPING AND

TRANSPORTATION

Investigate the height, width and the allowed carrying capacity
in the passage of transportation line. The total height, total width
and total weight should not exceed the related regulations.
Please consult

Hyundai

or other agents for the solutions.

In order to prevent the safety accidents from being occurred
during the shipment of the machine, clear the ice and snow as
well as other slippery materials on the dock and wagon.

NOTE:

During shipping, please follow the laws and regulations
about the shipment height, width, length and weight is-
sued by State and local authorities.

Perform the shipping according to the procedures shown below:
1. Use wedges to stop the wheels of trailer or truck before

shipping.

2. Do not allow the steering operation on the way for the ma-

chine being driven on to the trailer or the truck. You should
back the vehicle to the flat ground, and then perform the
steering operation

3. After the machine is fixed, use frame-fixed bumper to fix the

front and rear frames.

4. Lay the bucket down to the transportation vehicle, put the

shifting manipulating handle on “Neutral Gear” position, and
put the neutral gear locking plate on “Locking” position.

5. Pull up the button of parking brake to apply parking braking.
6. The engine is switched off, and all switches are put to Mid-

dle position or “OFF position. Pull out the starter key.

7. Close and lock all doors, then take away the cab key.
8. When you use truck or trailer to transport the machine, you

must use wedges to stop the wheels and use steel cables to

fix the machine, so as to prevent the machine from moving

during transportation.

«
...
45
46
47
48
49
...
»

Содержание HL630VL


































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HL630VL

Бренд: Parker Research Corp Страницы: 3

Бренд: S.I.T.A. Страницы: 32

Бренд: Latchways Страницы: 80

Бренд: Kapriol Страницы: 28

Бренд: GE Страницы: 24

Бренд: Jacobs Ladder Страницы: 16

ABS-Lock DH04 Series

Бренд: ABS Страницы: 4

Бренд: natus Страницы: 20

Dantec Keypoint G4

Бренд: natus Страницы: 42

Бренд: natus Страницы: 149

Бренд: Radial Engineering Страницы: 2

Бренд: Radial Engineering Страницы: 2

ST60+ SPEED INSTRUMENT

Бренд: Raymarine Страницы: 60

Бренд: Raymarine Страницы: 15

Бренд: RaycoWylie Страницы: 9

Бренд: Raven Страницы: 58

Бренд: Raven Страницы: 26

Бренд: Ravo Страницы: 114

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды