Hyundai HL630VL Скачать руководство пользователя | Manualshive

Страница: 142 / 161

background image

Transportation 5-1

Check federal, state and local laws and regulations regarding
weight, width, and length of machine and load before making
preparations for transporting on public roads or highways.
The hauling vehicle, trailer, and load must comply with all
applicable laws and regulations.
Check the intended route for road width, overhead clearances,
weight restrictions, and traffic control regulations. Special
approval or permits may be required.

During shipping, please follow the laws and regulations
about the shipment height, width, length and weight issued
by State and local authorities.

NOTE

Transportation

TRANSPORTING MACHINE

On Another Vehicle

• If the wheel loader is lifted onto another vehicle, the frame

lock bar must be in the "LOCKED" position.

• "APPLY" parking brake and set the frame lock bar in the

"LOCKED" position.

• Tie down (securing) the wheel loader – Use intended

attaching points for lifting. – Lock the articulated frame
joint.

Warning to customers: Removing from the machine the
counterweights, the front devices or other accessories
may affect the stability of the machine, thus causing the
accidental movement and serious injury or death. Our
company bears no legal responsibilities for the faults
induced from misusing the equipment. The machine the
counterweights or the front devices can be removed
only when the upper structure and the bottom structure
arrangement are consistent in direction.

DANGER

«
...
140
141
142
143
144
...
»

Содержание HL630VL


































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HL630VL

Бренд: BANLAW Страницы: 32

Бренд: Baker Instrument Company Страницы: 24

Бренд: jcb Страницы: 41

Бренд: Handler Страницы: 25

Бренд: Wahl Страницы: 47

Бренд: Califone Страницы: 7

Бренд: CALITEK Страницы: 16

Бренд: LAHTI PRO Страницы: 20

Бренд: LAHTI PRO Страницы: 16

Бренд: J&M Страницы: 53

Бренд: Qazqa Страницы: 2

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Konica Minolta Страницы: 32

Бренд: KaVo Страницы: 4

ORTHOPANTOMOGRAPH OP 3D

Бренд: KaVo Страницы: 40

KEY Laser III 1243

Бренд: KaVo Страницы: 103

EXTRAmatic 9040

Бренд: KaVo Страницы: 56

ESTETICA E70 Vision

Бренд: KaVo Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды