Hyundai HL630VL страница 24 Скачать руководство пользователя

Страница: 24 / 161

Safety 1-15

Battery

• During operation, the battery can produce combustible gas-

es which may cause explosion.

• Do not smoke while checking the level of electrolyte of the

battery.

• The electrolyte is an acidic substance, and it will hurt the

persons when it touches with skin or eyes.

Aether (if your machine is equipped with

Aether cold starter)

• Aether is a toxic and combustible substance.
• Inhaling Aether vapor or frequent touching of skin with

Aether will cause personal injury.

• There shall be adequate ventilation in the areas where

Aether is used.

• Do not smoke while replacing the Aether tank.
•

Pay attention to fire protection when using Aether.

• Do not put the replaced Aether tank in the living area or in

the cab.

• Do not put the Aether tank in a place with direct sunlight or

with an ambient temperature exceeding 39

℃

(120 F).

• Put the discarded Aether tank at a safety place. Do not drill

hole in it or heat it up.

• Put the Aether tank far away from the place where the

non-working persons are living.

Содержание HL630VL


































































































































































Результаты поиска

Содержание HL630VL

Отзывы:

Похожие инструкции для HL630VL

Бренды по названию

Популярные бренды

Hyundai HL630VL, Руководство оператора

Результаты поиска

Содержание HL630VL

Отзывы:

Похожие инструкции для HL630VL

Бренды по названию

Популярные бренды