Hyundai HL630VL страница 30 Скачать руководство пользователя | Manualshive

Страница: 30 / 161

background image

Safety 1-21

OPERATION OF LOADER

Matters needing attention on travelling

Do not shut off the engine while the machine is travelling. The
shutting off engine while the machine is travelling is dangerous.
You cannot manipulate the steering wheel effectively.
Do not operate the control handle of the attached device while
the machine is travelling.
Do not change the selected travel mode (quick/slow) while the
machine is travelling.
Fold the working device, making the outer end of the big arm
close to the machine as much as possible, and over 40-50cm
(16-20in) above the ground.
Do not travel on the obstacles or on the slope where the tip-
over of the machine is easily caused. Please bypass in advance
when you meet a slope or obstacle which can make the loader
tilt more than 10º from left side to right side and more than 30 º
from front side to rear side.
Please not suddenly turn a direction. Otherwise the working
device will strike the ground, making the machine lose balance
so that the machine or the devices in working area will be dam-
aged.
Drive slowly and avoid suddenly turn a direction while travelling
on the coarse ground.
Keep the permissible water level. The permissible water level
refers to the central line of the bridge.

Check first whether the bridge or the building can withstand the

weight of the machine while the machine is travelling on the
bridge or building. Observe the local authorization and follow its
instruction while the machine is travelling on the highway.

«
...
28
29
30
31
32
...
»

Содержание HL630VL


































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HL630VL

Бренд: Falcon Страницы: 52

Бренд: GE Страницы: 24

Бренд: Zenbooth Страницы: 60

Бренд: Abbott Страницы: 2

FreeStyle Libre

Бренд: Abbott Страницы: 3

Бренд: abc Страницы: 8

Бренд: Nitecore Страницы: 4

Бренд: Pari Страницы: 50

Бренд: Icare Страницы: 42

Бренд: Landi Renzo Страницы: 16

Бренд: IBM Страницы: 163

Бренд: National Instruments Страницы: 10

Бренд: Rath Страницы: 5

Бренд: U-Line Страницы: 9

Green Machine H-3518

Бренд: U-Line Страницы: 3

Бренд: Hach Страницы: 456

REBOUND DUAL ST

Бренд: Össur Страницы: 104

Бренд: Össur Страницы: 130

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды