Husqvarna F2203V4 страница 27 Скачать руководство пользователя

Страница: 27 / 166

CONTROLS 6

6.22

Locking the steering (EU)

Note

Danger of damage

The parked vehicle can roll away or fall over.

–

Park the vehicle on a firm and level surface.

400732-01

–

Park the vehicle.

–

Turn handlebar as far as possible to the right.

–

Lubricate the steering lock regularly.

Universal oil spray (

p. 155)

–

Insert the key for the steering lock into the steering lock
(

p. 24), turn it to the left, push it in, and turn it to the right.

Pull out the key for the steering lock.

Steering is no longer possible.

Info

Never leave the key for the steering lock in the steer-
ing lock.

6.23

Unlocking the steering (EU)

400731-01

–

Insert the key for the steering lock into the steering lock
(

p. 24), turn it to the left, pull it out, and turn it to the right.

Pull out the key for the steering lock.

The handlebar can now be moved again.

Info

Never leave the key for the steering lock in the steer-
ing lock.

Содержание F2203V4







































































































































































Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды

Husqvarna F2203V4, Руководство пользователя

Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды