background image

 

R&G Racing 

Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ 

Tel: +44 (0)1420 89007  Fax: +44 (0)1420 87301  

www.rg-racing.com

  Email

[email protected]

 

 

- 1 -

 

FITTING INSTRUCTIONS FOR PKS0059 KICKSTAND SHOE 

GENATA XRZ 125  2013- 

 
 
 
 
 
 
 
 
 
 
 
 

Please note that the way the kit is packed does not necessarily represent the way of 

mounting to the bike. 

 

T

HE PARTS SHOWN MAY BE REPRESENTATIVE ONLY 

(

FOR CLARITY OF INSTRUCTIONS ONLY

 

Please note that in cases where kits are packed with rubber washers holding the components onto the 

bolt – 

the rubber washers should be thrown away

 
 
 
 
 
 
 
 
 
 
 
 

 

 

 

 

 

                   BASE PLATE               CLAMP PLATE AND BOLTS 

 

TOOLS REQUIRED 

 

3mm A/F Allen key. 

FITTING INSTRUCTIONS 

 

Place the clamp plate (pictured above right) over the side stand base and position up the side 
stand shaft with the counter-sinks upper-most.  

 

Take the aluminium machined base plate (picture above left) and fit to the base of the side 
stand from underneath so it is aligned with the clamp plate. 

 

Apply a small amount (one drop) of Loctite Blue 242 to the end of the threaded area of each 
screw. 

 

Use the three counter-sunk bolts to secure in position, ensuring the inside edge of the clamp 
plate clamps down on the top of the side stand base 

Содержание PKS0059







Отзывы: