Husqvarna F2203V4 Скачать руководство пользователя

Страница: 37 / 166

PREPARING FOR USE 8

600868-01

–

Mount the steel sprocket.

–

Clean the motorcycle. (

p. 134)

–

Straighten the bent radiator fins carefully.

8.8

Preparing vehicle for high temperatures or slow riding

600868-01

–

Adjust the secondary drive to the road conditions.

Info

The engine oil heats up quickly when the clutch is
operated frequently due to an excessively high sec-
ondary ratio.

–

Clean the chain.

Chain cleaner (

p. 154)

–

Clean the radiator fins.

–

Straighten bent radiator fins carefully.

–

Check the coolant level. (

p. 120)

8.9

Preparing the vehicle for low temperatures or snow

102137-01

–

Mount the air filter rain cover.

Air filter rain cover (79006921000)

Info

Read the fitting instructions for

Husqvarna Motorcy-

cles

accessories.

Содержание F2203V4







































































































































































Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды

Husqvarna F2203V4, Руководство пользователя

Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды