Husqvarna F2203V4 Скачать руководство пользователя

Страница: 29 / 166

COMBINATION INSTRUMENT 7

401911-01

–

Wait for 5 seconds.

Combination instrument changes to the next menu item.
The

symbol flashes.

–

Press one of the buttons to select the 24 h display or 12 h
display for the clock.

401912-01

–

Wait for 5 seconds.

Combination instrument changes to the next menu item.
The

symbol flashes.

Resetting the time

–

Press the left button.

The value decreases.

Advancing the time

–

Press the right button.

The value increases.

401913-01

–

Wait for 5 seconds.

Combination instrument changes to the next menu item.
The

symbol flashes.

Shortening the service interval

–

Press the left button.

The value decreases.

Extending the service interval

–

Press the right button.

The value increases.

401914-01

Switching off the service interval display

–

Press and hold the left button.

off

appears in the display.

7.5

Adjusting the kilometers or miles

Info

If the unit is changed, the value

ODO

is retained and converted accordingly.

Condition

The motorcycle is stationary.

Содержание F2203V4







































































































































































Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды

Husqvarna F2203V4, Руководство пользователя

Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды