Husqvarna F2203V4 Скачать руководство пользователя страница 60

Страница: 60 / 166

12 SERVICE WORK ON THE CHASSIS

S03552-10

Main work

–

Remove screw

–

Remove screw

–

Open cable holder

in front of the left radiator and detach

the clutch line.

–

Take off the upper triple clamp with the handlebar and set
aside.

Info

Protect the components against damage by covering
them.
Do not kink the cables and lines.

H03683-10

–

Remove O-ring

and protective ring

–

Remove the lower triple clamp with the steering stem.

–

Remove the upper steering head bearing.

12.10

Installing the lower triple clamp

B01632-10

Main work

–

Clean the bearing and sealing elements, check for damage,
and grease.

High viscosity grease (

p. 154)

–

Position the lower triple clamp with the steering stem. Mount
upper steering head bearing.

–

Check whether upper steering head seal

is correctly posi-

tioned.

–

Mount protective ring

and O-ring

Содержание F2203V4







































































































































































Результаты поиска

Содержание F2203V4

Отзывы:

Бренды по названию

Популярные бренды

Husqvarna F2203V4, Руководство пользователя

Результаты поиска

Содержание F2203V4

Отзывы:

Бренды по названию

Популярные бренды