Husqvarna F2203V4 страница 23 Скачать руководство пользователя

Страница: 23 / 166

CONTROLS 6

6.13

Overview of indicator lights (US)

F03518-01

Possible states

Malfunction indicator lamp lights up/flashes yellow

–

The OBD has detected an error in the vehicle elec-

tronics. Come safely to a halt, and contact an autho-
rized Husqvarna Motorcycles workshop.
The fuel level warning lamp lights up yellow

–

The

fuel level has reached the reserve mark.

6.14

Opening fuel tank filler cap

Danger

Fire hazard

Fuel is highly flammable.

The fuel in the fuel tank expands when warm and can escape if overfilled.

–

Do not fuel the vehicle in the vicinity of open flames or lit cigarettes.

–

Switch off the engine for refueling.

–

Make sure that no fuel is spilled; particularly not on hot parts of the vehicle.

–

If any fuel is spilled, wipe it off immediately.

–

Observe the specifications for refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

–

Avoid skin, eye and clothing contact with fuel.

–

Immediately consult a doctor if you swallow fuel.

–

Do not inhale fuel vapors.

–

In case of skin contact, rinse the affected area with plenty of water.

–

Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.

–

Change your clothing in case of fuel spills on them.

–

Keep fuels correctly in a suitable canister, and out of the reach of children.

Note

Environmental hazard

Improper handling of fuel is a danger to the environment.

–

Do not allow fuel to enter the groundwater, the soil, or the sewage system.

F03499-10

–

Press release button

, turn the fuel tank filler cap counter-

clockwise, and lift it off.

Содержание F2203V4







































































































































































Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды

Husqvarna F2203V4, Руководство пользователя

Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды