Husqvarna F2203V4 Скачать руководство пользователя страница 101

Страница: 101 / 166

BRAKE SYSTEM 13

–

Remove the brake linings.

–

Clean the brake caliper and the brake caliper bracket.

–

Check that spring plate in the brake caliper and brake pad
sliding plate in the brake caliper bracket are fitted correctly.

S04472-01

–

Insert the new brake linings.

–

Mount pin

The spring plate engages in the groove on the pin.

Info

Always change the brake linings in pairs.

–

Mount cotter pins

–

Operate the foot brake lever repeatedly until the brake lin-
ings are in contact with the brake disc and there is a pressure
point.

F03485-10

–

Correct brake fluid level to marking

Brake fluid DOT 4 / DOT 5.1 (

p. 152)

–

Mount and tighten screw cap

with membrane

Info

Use water to immediately clean up any brake fluid that
has overflowed or spilled.

Содержание F2203V4







































































































































































Результаты поиска

Содержание F2203V4

Отзывы:

Бренды по названию

Популярные бренды

Husqvarna F2203V4, Руководство пользователя

Результаты поиска

Содержание F2203V4

Отзывы:

Бренды по названию

Популярные бренды