Husqvarna F2203V4 Скачать руководство пользователя

Страница: 155 / 166

SUBSTANCES 24

153

Fork oil (SAE 4) (48601166S1)

Standard/classification

–

SAE (

p. 156) (SAE 4)

Guideline

–

Use only oils that comply with the specified standards (see specifications on the container) and that exhibit
the corresponding properties.

Shock absorber fluid (SAE 2.5) (50180751S1)

Standard/classification

–

SAE (

p. 156) (SAE 2.5)

Guideline

–

Use only oils that comply with the specified standards (see specifications on the container) and that exhibit
the corresponding properties.

Super unleaded (ROZ 95)

Standard/classification

–

DIN EN 228 (ROZ 95)

Guideline

–

Only use super unleaded fuel that matches or is equivalent to the specified standard.

–

Fuel with an ethanol content of up to 10% (E10 fuel) is safe to use.

Info

not

use fuel containing methanol (e.g., M15, M85, M100) or more than 10% ethanol (e.g., E15,

E25, E85, E100).

Содержание F2203V4







































































































































































Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды

Husqvarna F2203V4, Руководство пользователя

Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды