Husqvarna F2203V4 страница 21 Скачать руководство пользователя

Страница: 21 / 166

CONTROLS 6

6.8

Turn signal switch (EU)

F03495-10

Turn signal switch

is fitted on the left side of the handlebar.

Possible states

Turn signal off

–

The turn signal switch is in the cen-

tral position.
Left turn signal, on

–

The turn signal switch is turned

to the left.
Right turn signal, on

–

The turn signal switch is

turned to the right.

6.9

Emergency OFF switch (EU)

F03496-10

The emergency OFF switch

is fitted on the right side of the

handlebar.

Possible states

Ignition off

–

In this position, the ignition circuit

is interrupted, a running engine stops, and a
non-running engine will not start.
Ignition on

–

In this position, the ignition circuit is

closed and the engine can be started.

6.10

Start button

F03497-10

(EU)

Start button

is fitted on the right side of the handlebar.

F03516-10

Start button

is fitted on the right side of the handlebar.

Possible states

• The start button

is in the basic position

• The start button

is pressed

–

The starter motor is actuated

in this position.

Содержание F2203V4







































































































































































Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды

Husqvarna F2203V4, Руководство пользователя

Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды