Husqvarna F2203V4 Скачать руководство пользователя страница 31

Страница: 31 / 166

COMBINATION INSTRUMENT 7

401914-01

Switching off the service interval display

–

Press and hold the left button.

off

appears in the display.

7.8

Speed, time, and DST distance 1

401901-01

–

Press one of the buttons until

DST

appears on the combina-

tion instrument.

KM/H

M/H

shows the speed.

shows the time.

DST

shows the distance since the last reset, such as between

two refueling stops.

Info

If the value of 39999.9 is exceeded,

DST

is automatically

reset to 0.0.

Press the left
button briefly.

Next display mode

Press the left
button for 3

–

5 seconds.

DST

can be preset to a value between 0.0 and

39999.9 by pressing the buttons.

Press the
right button
briefly.

Next display mode

Press the
right button
for 3

–

5 sec-

onds.

DST

is reset to 0.0.

7.9

Speed, time, and DST2 distance 2

401902-01

–

Press one of the buttons until

DST2

appears on the combina-

tion instrument.

KM/H

M/H

shows the speed.

shows the time.

DST2

shows the distance 2 since the last reset, such as between

two refueling stops.

Info

If the value of 39999.9 is exceeded,

DST2

is automatically

reset to 0.0.

Press the left
button briefly.

Next display mode

Содержание F2203V4







































































































































































Результаты поиска

Содержание F2203V4

Отзывы:

Бренды по названию

Популярные бренды

Husqvarna F2203V4, Руководство пользователя

Результаты поиска

Содержание F2203V4

Отзывы:

Бренды по названию

Популярные бренды