Husqvarna F2203V4 Скачать руководство пользователя

Страница: 95 / 166

BRAKE SYSTEM 13

F03508-10

–

Move the brake fluid reservoir mounted on the handlebar to a
horizontal position.

–

Remove screws

–

Take off cover

with membrane

S04462-10

–

Manually press the brake caliper toward the brake disc to
push back the brake pistons. Ensure that brake fluid does not
flow out of the brake fluid reservoir, extract some if neces-
sary.

Info

Make sure that you do not press the brake caliper
against the spokes when pushing back the brake pis-
tons.

–

Remove cotter pin

–

Pull out pin

–

Remove the brake linings.

–

Clean the brake caliper and the brake caliper bracket.

S04465-10

–

Check that spring plate

in the brake caliper and brake

pad sliding plate

in the brake caliper bracket are seated

correctly.

S04463-01

–

Insert the new brake linings.

–

Mount pin

Spring plate

engages in the groove on the pin.

Info

Always change the brake linings in pairs.

–

Mount cotter pins

–

Operate the hand brake lever repeatedly until the brake lin-
ings are in contact with the brake disc and there is a pressure
point.

Содержание F2203V4







































































































































































Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды

Husqvarna F2203V4, Руководство пользователя

Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды