Husqvarna F2203V4 Скачать руководство пользователя

Страница: 36 / 166

8 PREPARING FOR USE

102138-01

–

Mount the air filter sand cover.

Air filter sand cover (79006922000)

Info

Read the fitting instructions for

Husqvarna Motorcy-

cles

accessories.

600868-01

–

Clean the chain.

–

Mount the steel sprocket.

–

Grease the chain.

Universal oil spray (

p. 155)

–

Clean the radiator fins.

–

Straighten the bent radiator fins carefully.

8.6

Preparing the vehicle for riding on wet sand

102137-01

–

Mount the air filter rain cover.

Air filter rain cover (79006921000)

Info

Read the fitting instructions for

Husqvarna Motorcy-

cles

accessories.

600868-01

–

Clean the chain.

–

Mount the steel sprocket.

–

Grease the chain.

Universal oil spray (

p. 155)

–

Clean the radiator fins.

–

Straighten the bent radiator fins carefully.

8.7

Preparing the vehicle for riding on wet and muddy circuits

102137-01

–

Mount the air filter rain cover.

Air filter rain cover (79006921000)

Info

Read the fitting instructions for

Husqvarna Motorcy-

cles

accessories.

Содержание F2203V4







































































































































































Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды

Husqvarna F2203V4, Руководство пользователя

Результаты поиска

Содержание F2203V4

Отзывы:

Похожие инструкции для F2203V4

Бренды по названию

Популярные бренды