manualshive.com logo in svg

Hurco AB6, Руководство по установке

Поделиться
Скачать
Hurco AB6 Скачать руководство пользователя страница 48

Installation

Autobend 6 

November, 1999

2-9

Mounting Control Console with Optional Pendant Arm

To install the optional pendant arm to the press brake, follow these
instructions:

Caution

Make sure to position the pendant arm and the control console so
they do not interfere with the press brake’s operation.

1.

 

Determine the position of the pendant arm so the control
console is at the operator’s eye level. The pendant arm
projects approximately 40" (1016 mm) outward from the
press brake.

2.

 

Determine the correct position of the pendant arm bracket.
Locate and mark the centerline of its four (4) mounting holes
on the press brake’s surface. Be sure that the top of the
bracket is level and square against this surface.

3.

 

Drill and tap the holes for the bracket in the press brake.

4.

 

Use the four (4) 5/16-18 x 3/4 LG (M8 x 20 LG) SHCS to
attach the pendant arm bracket to the press brake.

5.

 

Attach the control console’s pendant arm bracket with the
four (4) M8 x 1.25 P x 16 LG SHCS to rear of the control
console.

Figure 2-5.  AB6 Control Console Mounted to Press Brake with Pendant Arm

Содержание AB6






































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды