Hurco AB6 Скачать руководство пользователя страница 136

Страница: 136 / 165

Installation

Autobend 6

November, 1999

2-97

Hold the magnet as a template against the ram or bed in the
previously determined location. Mark the centerlines of the
mounting holes.

Drill holes for either 8-32 or 4 mm screws.

Clean the mounting surface and secure the magnet in place.

Using the retract sensor assembly as a template, hold the
sensor against the side wall in the previously determined
location.

10.

Mark the centerlines of the mounting holes on the adjustment
bracket.

11.

Drill and tap the holes for either 10-32 or 4 mm screws.

12.

Route the retract cable from the sensor to the AB6 power
cabinet.

Caution

Avoid routing the cable adjacent to any press brake electrical cables.

13.

Install a cord-grip conduit fitting into the 1/2" (12.7 mm) hole
in the bottom of the AB6 power cabinet.

14.

Route the cable through the fitting and into the AB6 power
cabinet. Remove excess cable leaving only 10" (254 mm) of
cable inside the cabinet.

15.

Strip back 4" (100 mm) of outer insulation and cut off the
shield.

16.

Strip back 1/4" (6 mm) of insulation from the individual
wires.

17.

Cut off shield wire.

Содержание AB6






































































































































































Результаты поиска

Содержание AB6

Отзывы:

Бренды по названию

Популярные бренды

Hurco AB6, Руководство по установке

Результаты поиска

Содержание AB6

Отзывы:

Бренды по названию

Популярные бренды