manualshive.com logo in svg

Hurco AB6, Руководство по установке

Поделиться
Скачать
Hurco AB6 Скачать руководство пользователя страница 122

Installation

Autobend 6

November, 1999

2-83

15.

 

Adjust the switch to actuate at the top of the stroke for
mechanical press brakes and at the upper mid-stroke of the
foot treadle for upacting press brakes.

16.

 

Route the other end of the cable to the Large AB6 power
cabinet. Do not route this cable adjacent to any electrical
cables.

17.

 

Route about 10" (254 mm) of the cable through the fitting
into the Large AB6 power cabinet.

18.

 

Strip back 2" (51 mm) of the outer insulation.

19.

 

Cut off the shield and dispose.

20.

 

Strip back 1/4" (6 mm) of insulation on each of the
individual wires.

21.

 

Locate the Relay board mounted inside the back of the
Large AB6 power cabinet.

22.

 

Locate the TB14 connector in the upper right-hand corner
of the Relay board.

23.

 

Remove the TB14 connector.

24.

 

Using a small screwdriver, open position #6 (labeled ADV)
and insert the clear wire.

25.

 

Open position #7 (labeled ADV RTN) and insert the black
wire.

26.

 

Replace the TB14 connector.

Important

The  “Relay Board” and “TB14 Connector” sections earlier in this
chapter contain information about locating the connector and
opening the position on it.

Содержание AB6






































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды