Hurco AB6 Скачать руководство пользователя страница 107

Страница: 107 / 165

Installation Manual

2-68

Revision E

Hurco

Loosen the cord-grip conduit fitting.

Route the two-conductor cable through the fitting into the
speed change switch and up to the connection points.

Connect to unused switch terminals #1 and #2.

Replace the cover on the speed change switch.

Caution

Do not route the cable adjacent to any electrical cables.

Route the other end of the cable to the AB6 power cabinet.
Do not route this cable adjacent to any electrical cables.

Remove the 7/8" (22.22 mm) diameter knock out for the 1/2"
conduit fitting at the bottom of the AB6 power cabinet.

Route about 10" (254 mm) of the cable through the fitting
into the AB6 power cabinet.

10.

Strip back 2" (51 mm) of the outer insulation.

11.

Cut off the shield and dispose.

12.

Strip back 1/4" (6 mm) of insulation on each of the individual
wires.

13.

Locate the Main board mounted inside the AB6 power
cabinet on the left-hand side.

14.

Locate and remove the J8 connector in the center lower
portion of the Main board.

15.

Using a small screwdriver, open position #1 (labeled
ADVANCE) and insert the clear wire.

16.

Open position #7 (labeled 24 COM) and insert the black
wire.

17.

Replace the J8 connector.

Important

The “Main Board” and “J8 Connector” sections earlier in this
chapter contain information about locating the connector and
opening the position on it.

Содержание AB6






































































































































































Результаты поиска

Содержание AB6

Отзывы:

Бренды по названию

Популярные бренды

Hurco AB6, Руководство по установке

Результаты поиска

Содержание AB6

Отзывы:

Бренды по названию

Популярные бренды