Hunter Douglas Douette PowerView Скачать руководство пользователя страница 4

Страница: 4 / 44

GETTING STARTED

Thank you for purchasing Hunter Douglas Duette

Vertiglide

™

honeycomb shades. With proper

installation, operation, and care, your new shades will provide years of beauty and performance.

To get started, unpack the shade and remove
all foam/packaging materials. Check that all
parts shown on the packing list are included
with the order. Please thoroughly review
this instruction booklet before beginning the
installation.

IMPORTANT:

Cords are wrapped around

a cord organizer located approximately 6"
from the top of the moving rail. Please do not
unwrap the cords until instructed to do so.

Tools and Fasteners Needed

■

Flat blade and magnetic-tipped Phillips screwdrivers

■

Level (laser level is recommended)

■

Measuring tape and pencil

■

Power drill,

" drill bit, and

" hex driver

■

Scissors

In addition, you will need fasteners designed to work with your specific mounting surface(s).

■

#6 Hex Head Screws (Provided).

Two 1

" screws are provided per installation bracket.

■

Longer #6 Hex Head Screws (Not Provided).

If using spacer blocks, use #6 screws long

enough for a secure attachment.

■

Speed Nuts and Screws (Provided).

Extension brackets come with speed nuts and screws.

■

Drywall Anchors (Not Provided).

Use drywall anchors when mounting into drywall.

Speed Nut

and Screw

(Two Provided with

Each Extension Bracket)

#6 x 1

Hex Head Screw

(Provided)

Longer #6 Hex Head Screw

for Use with Spacer Blocks

(Not Provided)

Do Not

Unwrap

Cords

Содержание Douette PowerView













































Результаты поиска

Содержание Douette PowerView

Отзывы:

Похожие инструкции для Douette PowerView

Бренды по названию

Популярные бренды

Hunter Douglas Douette PowerView, Установка Эксплуатация Уход

Результаты поиска

Содержание Douette PowerView

Отзывы:

Похожие инструкции для Douette PowerView

Бренды по названию

Популярные бренды