Hunter Douglas Douette PowerView Скачать руководство пользователя страница 9

Страница: 9 / 44

INSTALLATION – OUTSIDE MOUNT

■

Attach the spacer blocks and installation brackets
with #6 hex head mounting screws long enough for
a secure installation. (See chart below.) Longer screws
are not provided.

■

➤

The top of the spacer blocks should be at the
desired shade height.

■

➤

The front edges of the installation brackets must
be level and aligned to each other.

CAUTION:

Use drywall anchors when mounting

into drywall.

CAUTION:

The rear of the spacer blocks must be flush against a flat surface. Do not mount

spacer blocks and installation brackets on curved molding.

3" (Not provided; up to 1

" of spacer blocks/shims)

" (Not provided; up to 1

" of spacer blocks/shims)

Never use more than 1

" of spacer blocks/shims!

IMPORTANT:

The provided 1

" screws can only

be used with a maximum of one

" shim.

You will

need to supply longer screws if additional
clearance is required.

A minimum 1

" length of screw threads must

extend beyond the last spacer block or shim.
Use appropriate wall anchors when mounting
into drywall.

2" (Not provided; up to

" of spacer blocks/shims)

" Minimum

Shim

Maximum of One

Shim with Provided

" Screws

Longer Screw

(Not Provided)

Maximum

Содержание Douette PowerView













































Результаты поиска

Содержание Douette PowerView

Отзывы:

Похожие инструкции для Douette PowerView

Бренды по названию

Популярные бренды

Hunter Douglas Douette PowerView, Установка Эксплуатация Уход

Результаты поиска

Содержание Douette PowerView

Отзывы:

Похожие инструкции для Douette PowerView

Бренды по названию

Популярные бренды