Hunter Douglas Douette PowerView Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 44

background image

INSTALLATION

25

■

■

Plug the long end of the cable into the
socket on the second battery wand.

■

■

Place the battery wand into the front
channel of the headrail.

If Your Order Came with One Battery Wand Only...

■

■

Plug the single power cable from the motor into the socket on the battery wand.

■

■

Place the battery wand into the front channel of the headrail. The front lip on the channel
holds the wand in position.

Second Battery Wand

«
...
25
26
27
28
29
...
»

Содержание Douette PowerView













































Отзывы:

Нет отзывов

Похожие инструкции для Douette PowerView

Бренд: fantastic furniture Страницы: 15

Бренд: DANDELION Страницы: 7

Бренд: ofichairs Страницы: 2

Бренд: Oak furnitureland Страницы: 6

Бренд: Saint Birch Страницы: 12

Бренд: Coaster Страницы: 2

OBRA SIDEBOARD BZ-1060-20

Бренд: Moe's Страницы: 2

Бренд: Amart Furniture Страницы: 14

Бренд: BROSA Страницы: 4

VIS A VIS 01741

Бренд: TRIBU Страницы: 2

Lacy Mid Sleeper

Бренд: Happy Beds Страницы: 54

Бренд: Homestyles Страницы: 7

Бренд: Home Decorators Collection Страницы: 16

Бренд: ML MEBLE Страницы: 29

Бренд: Pulsar Страницы: 2

84021BLK-01-KD-U

Бренд: Linon Страницы: 10

Industrial Metal and Wood Tool Cart

Бренд: Whalen Страницы: 5

Бренд: GAMADECOR Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды