Hunter Douglas Douette PowerView Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 44

background image

OPERATION

29

Resetting Shade Programming

This reset erases all shade programming from memory, including group assignments, preventing
any input device from operating the shade. Its primary use is during installation to correct group
and network assignments. This reset does not affect travel limits.

1. Press and hold the manual control button for 12 seconds. The shade will move slightly after 6

seconds, then again after 12 seconds. Release the button.

2. Refer to “Joining a Shade to a Group” on page 27 to program the shade to a group.

Dual Operation

An innovative feature of Duette

®

Vertiglide

™

with PowerView

™

Motorization is dual operation: the

shade can be operated either motorized or manually. The drive belt automatically disengages
after each motorized use, allowing the shade to be traversed manually. When the remote is
used, the drive belt automatically re-engages for motorized operation.

With dual operation, the PowerView App can be used for precise positioning of the shade. The
App knows the position of the shade when the motor re-engages, so if the shade has been
moved manually, the App positions the shade correctly.

«
...
29
30
31
32
33
...
»

Содержание Douette PowerView













































Отзывы:

Нет отзывов

Похожие инструкции для Douette PowerView

Бренд: ofichairs Страницы: 2

Бренд: pakoworld Страницы: 2

Бренд: Safavieh Страницы: 4

Бренд: Safavieh Страницы: 4

Бренд: Safavieh Outdoor Страницы: 8

Бренд: Unfinished Furniture of Wilmington Страницы: 5

Бренд: Unfinished Furniture of Wilmington Страницы: 7

DREW BARRYMORE FLOWER HOME 8685

Бренд: µ-Dimension Страницы: 15

Бренд: &Tradition Страницы: 3

Бренд: µ-Dimension Страницы: 4

PALETTE TABLE JH7

Бренд: &Tradition Страницы: 3

PALETTE DESK JH9

Бренд: &Tradition Страницы: 2

Бренд: µ-Dimension Страницы: 4

Бренд: µ-Dimension Страницы: 4

Бренд: µ-Dimension Страницы: 4

Бренд: Gautier Страницы: 8

OSBOURNE 383598

Бренд: Next Страницы: 9

RISE AND RECLINE CHAIR

Бренд: Comfomatic Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды