Hunter Douglas Douette PowerView Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 44

background image

INSTALLATION

23

10-Pin Port

6-Pin Port

Connector Orientation

■

■

Reconnect the 10-pin connector to the 10-pin port on the manual control button.

■

➤

There are two ports on the manual control button: one 10-pin port and one 6-pin
port. The 6-pin port is for a dry contact connection to interface with home automation
systems.

■

➤

The pins in the 10-pin port are offset toward the button side of the manual control
button assembly. Be sure to orient the holes on the connector the same way.

IMPORTANT:

Do not force the connector into the port. If the connector is oriented correctly,

it should fit onto the pins in the port with little effort.

■

■

Affix the manual control button to the wall or molding.

■

➤

Peel the backing from the double-sided tape on the rear of the assembly.

■

➤

Press the manual control button onto the mounting surface, as shown.

IMPORTANT:

Choose a location where the manual control button will not be obstructed by

the valance or side rails, and where the wire will not be pinched.

«
...
23
24
25
26
27
...
»

Содержание Douette PowerView













































Отзывы:

Нет отзывов

Похожие инструкции для Douette PowerView

JENSEN 5-PIECE DINING SET

Бренд: Canvas Страницы: 20

Бренд: Unfinished Furniture of Wilmington Страницы: 5

Бренд: Unfinished Furniture of Wilmington Страницы: 7

Бренд: KEEPREAPER Страницы: 10

Бренд: Target Страницы: 10

Бренд: garofalo Страницы: 12

Shefback C-1602

Бренд: Unfinished Furniture of Wilmington Страницы: 4

Бренд: Rasson Страницы: 7

Бренд: East West Furniture Страницы: 4

Бренд: Walker Edison Страницы: 7

Бренд: DIVERSIFIED WOODCRAFTS Страницы: 6

Open Plan Tall Bookcase

Бренд: BluDot Страницы: 8

Бренд: Tecnos Страницы: 15

Casper Office Chair

Бренд: fantastic furniture Страницы: 7

M22105HD 2722241

Бренд: Backyard Creations Страницы: 2

Panchito RecBK-2F-OTMBK

Бренд: Möbelix Страницы: 4

Бренд: Unfinished Furniture of Wilmington Страницы: 4

Бренд: Tech Craft Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды