Hunter Douglas Douette PowerView Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 44

background image

INSTALLATION

21

■

■

Tension the cord.

IMPORTANT:

When the cord is properly tensioned, the moving rail slides easily yet holds

its position anywhere along its travel.

■

➤

Slide the cord tensioner along its channel in the headrail until the cord is taut.

■

➤

Manually open and close the fabric stack several times. This evenly distributes tension
throughout the shade.

■

➤

If necessary, readjust the cord tensioner by sliding it until the cord is taut. Check to
ensure the proper tension. Make any needed adjustments by sliding the cord tensioner
in its channel so that the moving rail slides easily and holds its position anywhere along
its travel.

«
...
21
22
23
24
25
...
»

Содержание Douette PowerView













































Отзывы:

Нет отзывов

Похожие инструкции для Douette PowerView

Бренд: XYBIX SYSTEMS Страницы: 29

Бренд: Safco Страницы: 3

Бренд: PAIDI Страницы: 9

Бренд: Fashion Sewing Cabinets Of America Страницы: 2

Бренд: FAirway Страницы: 4

TILL 20 90 01 62

Бренд: Links Страницы: 8

Бренд: Laura Ashley Страницы: 3

Бренд: &Tradition Страницы: 3

Бренд: Furniture of America Страницы: 5

Бренд: JWA Страницы: 15

Бренд: Workrite Страницы: 10

Бренд: Original Steifensand Страницы: 16

Бренд: Walker Edison Страницы: 4

Бренд: Ameriwood HOME Страницы: 12

Бренд: Mainstays Страницы: 15

Бренд: D-Bodhi Страницы: 2

Palladia Highboy 411626

Бренд: Sauder Страницы: 36

ZIG ZAG DIVIDER 25-4658

Бренд: Natural Signature Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды