Hunter Douglas Douette PowerView Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 44

background image

INSTALLATION

24

Connect the Power Source

NOTE:

When power is connected to the motor, if your shade is a right stack, a green LED inside

the manual control button housing will flash to indicate the shade is ready for operation. If your
shade is a left stack, a green LED then red LED will flash to indicate the shade is ready for
operation.

■

■

Refer to the appropriate page based on your order.

■

➤

For battery wands, see below.

■

➤

For a DC power supply, see page 26.

If You Have Battery Wands...

Two battery wands come with Duette

®

Vertiglide

™

PowerView

™

shades 54" wide or wider.

Shades less than 54" wide will come with one battery wand only.

Install Batteries into the Battery Wands

■

■

Squeeze the cap latch to release the cap.

■

■

Remove the cap from the battery wand.

■

■

Install the batteries according to the
instructions on the battery wand label.

■

➤

Hunter Douglas recommends AA alkaline batteries for use with our battery-powered
shades. These will provide more than one year of operation, depending on usage.
Lithium and rechargeable batteries are not recommended.

■

■

Replace the cap.

■

➤

Align the tab with the end of the wand.

■

➤

Press the cap on until it latches.

Plug the Power Cable into the Battery Wands

With two battery wands, the power cable from
the motor splits into a “Y”.

■

■

Plug the short end of the power cable
from the motor into the socket on the first
battery wand.

■

■

Place the battery wand into the front
channel of the headrail. The front lip on the
channel holds the wand in position.

Tab

Slot

Cap

Latch

Battery

Wand

Squeeze

From

Motor

First Battery Wand

«
...
24
25
26
27
28
...
»

Содержание Douette PowerView













































Отзывы:

Нет отзывов

Похожие инструкции для Douette PowerView

Бренд: Naterial Страницы: 28

Бренд: ZEITRAUM Страницы: 2

Бренд: ofichairs Страницы: 2

Бренд: Sango Страницы: 10

Бренд: Hülsta Страницы: 16

Бренд: Westfalia Страницы: 2

Бренд: Forte Страницы: 20

ARC COFFEE TABLE

Бренд: Sage Living Home & Decor Страницы: 2

Бренд: BCP Страницы: 4

LEGACY A414025109

Бренд: Broyhill Страницы: 7

Бренд: Itatiaia Страницы: 2

Бренд: WIEMANN Страницы: 3

Бренд: Okamura Страницы: 4

Бренд: MAAX Страницы: 16

Бренд: Amerihome Страницы: 2

Bowfield 315900KE

Бренд: Coaster Страницы: 6

Бренд: comfortel Страницы: 4

Бренд: KD-MISSION Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды