Hunter Douglas Douette PowerView Скачать руководство пользователя страница 39

Страница: 39 / 44

CARE

Problem

The fabric billows out when moving the shade to the stacked (fully open)
position.

Solution

Increase the cord tension. Slide the cord tensioner toward the fabric stack to
slightly increase the tension. See “Set Cord Tension” beginning on page 17.

Problem

The cord tensioner does not lock into place.

Solution

If using a valance, place a valance bracket up against the cord tensioner to act
as a stop, preventing the tensioner from sliding.

Determine the correct location for the cord tensioner. Hold it in place and insert
a small screw into the channel next to the cord tensioner.

Problem

The shade is not vertically aligned.

Solution

Check that the installation brackets are level and aligned. Shim the installation
brackets to level the headrail, if necessary.

Check that the headrail is completely inserted into the installation brackets. See
“Mount the Headrail” on page 8 (OB) or page 10 (IB).

Adjust the screws on the moving rail bracket. Review the adjustment procedures
on page 20.

Problem

A fabric carrier needs to be reattached.

Solution

Place the carrier between the fabric cells.

Push the pin through the hole in the fabric cells.

Snap the hole at the bottom of the fabric
carrier onto the pin.

Fabric Carrier

Содержание Douette PowerView













































Результаты поиска

Содержание Douette PowerView

Отзывы:

Похожие инструкции для Douette PowerView

Бренды по названию

Популярные бренды

Hunter Douglas Douette PowerView, Установка Эксплуатация Уход

Результаты поиска

Содержание Douette PowerView

Отзывы:

Похожие инструкции для Douette PowerView

Бренды по названию

Популярные бренды