2. Remove two screws attaching compartment door lock
cover to compartment door.
3. Remove one bolt attaching lock to compartment door
reinforcement and remove lock.
INSTALLATION
To install, reverse procedure of removal and check door
lock striker adjustment.
REAR COMPARTMENT DOOR
LOCK CYLINDER
(All Models 1C, 1D, 2C, 2D and 3D)
REMOVAL
1. Raise compartment door.
2. Through opening between compartment door and com-
partment door reinforcement remove lock cylinder hous-
ing retainer (spring clip).
3. Remove lock cylinder assembly.
INSTALLATION
To install, reverse procedure of removal.
REAR COMPARTMENT DOOR
(All Models 1948 thru 1954)
ADJUSTMENT
1. Adjustment is accomplished by loosening the upper sup-
port hinge bolts, this will allow the compartment door to
be shifted forward or toward the rear or side to side.
2. Loosening the body hinge support bolts will allow the
compartment door to be raised or lowered.
3. Adjust compartment door lock striker if necessary.
REAR COMPARTMENT DOOR
STRIKER
(All Models 1951 thru 1954)
ADJUSTMENT
1. The rear compartment door should lock by slight hand
pressure.
2. To adjust, loosen the two screws, then raise or lower the
striker in the elongated holes. Raising the striker upward
causes the door to close with less pressure and lowering
the striker causes the door to close more tightly.
3. Tighten both screws securely after making adjustment.
NOTE: The striker is positioned properly when the top of
the striker is 3/32" above the top of the channel on the
rear compartment panel, Figure 111.
REAR COMPARTMENT DOOR
HINGE (RIGHT OR LEFT)
(All Models 1948 thru 1954)
REMOVAL
1. Raise compartment door.
2. Mark original position at both attaching places before
removing hinge to facilitate installation.
3. Place a block of wood between compartment door and
rear roof panel to hold compartment door in position.
4. Remove the attaching bolts from upper hinge bracket to
compartment door and the bolts attaching the lower
hinge bracket to body reinforcement.
5. Remove the hinge assembly.
INSTALLATION
To install, reverse procedure of removal and check ad-
justment.
REAR COMPARTMENT DOOR
WEATHERSTRIP
(All Models 1948 thru 1954)
INSTALLATION
1. Prior to installation, make sure all surfaces to be ce-
mented are clean.
2. With a brush, coat both the cementing surface of the
rubber weatherstrip and the corresponding surface with a
light coat of weatherstrip adhesive.
3. Position weatherstrip and working across the bottom and
up each side, press the weatherstrip firmly into position.
NOTE: Allow sufficient time for drying before closing
compartment door.
BODY MANUAL 78
Содержание 1948 Commodore
