11 BODY MANUAL
19. The sedan rear door uses a handle with a contour as
shown at (U)
.
On the 480-490 Models and the 501, 502, 503, 504 models,
sedan front door s and brougham and coupe doors use the
handle with the contour as shown at (M), Figure 18. The
sedan rear door handle contour is shown a t (N), Figure 18.
Failure of the lock to hold the door closed may be due to
the door rotor latch being held open because of lack of lubri-
cation or to water having frozen on the lock. Re-lubrication of
the door lock will correct the condition in either case.
NOTE: Door locks should be lubricated at least twice a year
or about every 5000 miles.
This can be done by removing the door outside handle and
cleaning the lock with air, inserting the hose nozzle through
the handle opening in the door. The lock should then be
lubricated with Hudson Lock-Ease Oil by inserting the oil can
spout through the handle opening.
With the exception of the correction of frozen remote
control links, the foregoing operations can be performed with-
out removing the inside trim or door locks.
DOOR LOCK RELEASE PUSH
BUTTON ADJUSTMENT
(Models IC, 1D, 2C, 2D and 3D)
The proper operation of the front and rear door push
buttons is obtained when the measurements are made as
shown in Figure 20.
The measurement a t upper left is obtained by adding
washers 1/32" thick as required, at point "A". The measure-
ment shown below is controlled by the threaded plunger and
button. The object is to effect a door release before the button
outer end passes into the retainer.
DOOR STRIKER PLATE
(All Models 1948 thru 1953
Except 1C, 1D, 2C, 2D and 3D)
The door striker plate (3), Figure 21, is mounted on the
body pillar and is attached to a tapping plate on the inside of
the pillar.
FIGURE 20
REMOVAL
Remove three Phillips head screws (1) from striker plate
and remove plate.
NOTE: With the striker plate removed, to remove tapping
plate (2), loosen trim (4) at pillar and lift plate out of
retainer (5).
FIGURE 21
ADJUSTMENT
1. Loosen the three, Phillips head screws (1) sufficiently to
allow striker plate to be moved easily with the fingers.
2. Adjust height of striker plate to give correct alignment with
the door latch bar.
3. Adjust inward position of striker plate to hold door firmly
against weatherstrips.
Содержание 1948 Commodore
