right hand link to bring the bend into closer engagement with
the stop of the operating lever.
When in proper adjustment the rear deck handle should have
approximately 1/4" spring back from the full closed position
with the handle unlocked.
REAR COMPARTMENT DOOR
LOCK CYLINDER
(All Models 1951)
REMOVAL
1. Raise compartment door and remove the name plate for
the 4A Series cars. On all other models the lock cylinder
may be removed as outlined in paragraphs 2,3 and 4.
2. Use a small center punch to spot center position for 1/16"
drill and drill out drive screw, Figure 111. The drive screw
has an over-all length of 1/4".
3. When the drive screw has been removed the lock cylinder
retaining set screw can be removed with a 3/32" Allen
wrench.
4. Remove lock cylinder.
NOTE: If it is necessary to replace the door lock cylinder
cover, refer to the insert, Figure 111, covering the 4A
Series installation and the arrow indicating the 5A, 6A, 7A
and 8A Series installation.
INSTALLATION
To install, reverse procedure of removal. Always install a
drive screw to close the opening in set screw.
FIGURE 112
NOTE: Figure 112, shows the service lock cylinder which
is interchangeable on all "A" Series Models. These service
locks have a
have a long shank to cover all models and must be reworked
as illustrated for the different models.
REAR COMPARTMENT DOOR
LOCK
(All Models 1951)
REMOVAL
1. Remove rear compartment door name plate (4A only).
2. Remove rear compartment door license lamp with lock
cylinder as an assembly. (4A only.) On Models 5A, 6A,
7A and 8A, remove the ornament and door lock cylinder
as an assembly.
3. Re move two Phillips head sheet metal screws and tow
1/4-28" x 1/2" screws attaching the rear compartment
door lock cover to compartment door (7/16" socket).
4. Remove one bolt, shakeproof and flat washer attaching
lock to compartment door reinforcement and remove
lock.
INSTALLATION
To install, reverse procedure of removal, and check
door lock striker adjustment.
REAR COMPARTMENT DOOR
LOCK CYLINDER
(All Models 1952 thru 1954
Except 1C, 2C, 1D, 2D and 3D)
REMOVAL
1. Raise compartment door and remove the bolts attaching
the name plate and lock cylinder.
2. Remove the retaining clip attaching the lock cylinder to
the name plate and remove lock cylinder.
INSTALLATION
To install, reverse procedure of removal.
REAR COMPARTMENT DOOR
LOCK
(All Models 1952 thru 1954)
REMOVAL
1. Remove compartment door lock cylinder (See
"Compartment Door Lock Cylinder Removal").
77 BODY MANUAL
Содержание 1948 Commodore
