Huawei Airbridge BTS3606A Скачать руководство пользователя страница 131

Страница: 131 / 141

Installation Manual – BTS3606A Cabinet Installation
Airbridge BTS3606&3606A CDMA Base Station

Chapter 5 Installing Cables

Huawei Technologies Proprietary

5-53

Lead the positive cable, the negative cable, the access control and temperature

sensor cable, and the grounding cable out of the outlet at the bottom of the cabinet.

Connect them to the BTS3606A cabinet.

For positions of the outlets, see Figure 5-56.

(1) Outlet of –48 V power cable

(2) Outlet of GND cable

(3) Outlet of access control and temperature alarm cable
(4) Outlet of hot plate power cable

(5) Auxiliary outlet of –48 V power cable

(6) Auxiliary outlet of GND cable

(7) Outlet of PGND cable

Figure 5-56

Outlets of the battery cabinet

Paint the wiring terminals of the access control and temperature sensor and the

air-break switch with silicon gel to make them waterproof.

5.10.4 Installing Cables between Battery Cabinet and BTS3606A Cabinet

Lead cables of the battery cabinet through its pedestal. Connect them to the basic

cabinet of BTS3606A through waterproof components at the bottom of the BTS3606A

cabinet.

Table 5-10 provides the connection positions.

Table 5-10

Connection of external cables of the storage battery

Cable name

Connection position

Positive cable GND wiring terminal inside the BTS3606A cabinet

Negative
cable

–48 V wiring terminal inside the BTS3606A cabinet

Access control
alarm cable

2-pin connector (green) of the column at the back of BTS3606A
cabinet.

The connector is bound to the column in the front of the cabinet.

Temperature
sensor cable

2-pin socket (white) from the BTS3606A power monitoring board.

The socket is bund at the bundling rack of the waterproof module
at the bottom of the cabinet.

PGND cable

Grounding bar of BTS3606A cabinet

Содержание Airbridge BTS3606A














































































































































Результаты поиска

Содержание Airbridge BTS3606A

Отзывы:

Похожие инструкции для Airbridge BTS3606A

Бренды по названию

Популярные бренды

Huawei Airbridge BTS3606A, Руководство по установке

Результаты поиска

Содержание Airbridge BTS3606A

Отзывы:

Похожие инструкции для Airbridge BTS3606A

Бренды по названию

Популярные бренды