Huawei Airbridge BTS3606A Скачать руководство пользователя страница 40

Страница: 40 / 141

Installation Manual – BTS3606A Cabinet Installation
Airbridge BTS3606&3606A CDMA Base Station

Chapter 3 Installing Cabinet and Cabinet Equipment

Huawei Technologies Proprietary

3-1

Chapter 3 Installing Cabinet and Cabinet

Equipment

This chapter introduces how to install the BTS3606A cabinet, the battery cabinet, and

the equipment inside these cabinets.

3.1 Installation of Cabinet

During the installation of combined cabinets, the extension cabinet is installed in the

same way as the basic cabinet.

To install the basic cabinet, proceed as follows:

1) Position

the

cabinet.

Level the cabinet.

Fasten the cabinet.

4) Install

accessories.

3.1.1 Positioning Cabinet

Lift and place slowly the cabinet over the base and align the installation holes on the

bottom of the cabinet with those on the base.

Caution:

An empty cabinet weighs 450 kg (992 lb.). Confirm the lifting capability of the lifting

equipment beforehand.

When lifting the cabinet, make sure that all the four lugs are reliably hooked, the

angle between the lifting rope and the top of the cabinet is at least 60

, and the

cabinet is level. Installers must stay away from the cabinet when lifting it and make

sure that the front and rear doors are closed.

When installing the cabinet in bad conditions (for example, when there is strong

wind), pay extra attention to the gravity center of the cabinet to prevent the cabinet

from slanting.

If the cabinet cannot be lifted on site, position the cabinet according to the bearing

points shown in Figure 3-1 and site characteristics.

Содержание Airbridge BTS3606A














































































































































Результаты поиска

Содержание Airbridge BTS3606A

Отзывы:

Похожие инструкции для Airbridge BTS3606A

Бренды по названию

Популярные бренды

Huawei Airbridge BTS3606A, Руководство по установке

Результаты поиска

Содержание Airbridge BTS3606A

Отзывы:

Похожие инструкции для Airbridge BTS3606A

Бренды по названию

Популярные бренды