HPE FlexNetwork 5130 HI SERIES Скачать руководство пользователя страница 65

Страница: 65 / 286

Port Status Priority Oper-Key Flag

--------------------------------------------------------------------------------

GE1/0/1 S 32768 1 {ACDEF}

GE1/0/2 S 32768 1 {ACDEF}

GE1/0/3 S 32768 1 {ACDEF}

Remote:

Actor Partner Priority Oper-Key SystemID Flag

--------------------------------------------------------------------------------

GE1/0/1 1 32768 1 0x8000, 000f-e267-57ad {ACDEF}

GE1/0/2 2 32768 1 0x8000, 000f-e267-57ad {ACDEF}

GE1/0/3 3 32768 1 0x8000, 000f-e267-57ad {ACDEF}

The output shows that:

•

Link aggregation group 1 is a Layer 2 dynamic aggregation group.

•

The aggregation group contains three Selected ports.

Layer 2 aggregation load sharing configuration example

Network requirements

On the network shown in

Figure 14

, perform the following tasks:

•

Configure two Layer 2 static aggregation groups 1 and 2 on Device A and Device B,
respectively.

•

Enable VLAN 10 at one end of the aggregate link to communicate with VLAN 10 at the other
end.

•

Enable VLAN 20 at one end of the aggregate link to communicate with VLAN 20 at the other
end.

•

Configure link aggregation groups 1 and 2 to load share traffic across aggregation group
member ports.

{

Configure link aggregation group 1 to load share packets based on source MAC addresses.

{

Configure link aggregation group 2 to load share packets based on destination MAC
addresses.

Figure 14 Network diagram

Configuration procedure

Configure Device A:
# Create VLAN 10, and assign the port GigabitEthernet 1/0/5 to VLAN 10.

Содержание FlexNetwork 5130 HI SERIES































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI SERIES

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI SERIES

Бренды по названию

Популярные бренды

HPE FlexNetwork 5130 HI SERIES, Руководство по настройке

Результаты поиска

Содержание FlexNetwork 5130 HI SERIES

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI SERIES

Бренды по названию

Популярные бренды