HPE FlexNetwork 5130 HI SERIES Скачать руководство пользователя страница 41

Страница: 41 / 286

To configure the MAC Information mode:

Step Command

Remarks

Enter system view.

system-view

N/A

Configure the MAC
Information mode.

mac-address information mode

{

syslog

trap

}

The default setting is

trap

Configuring the MAC change notification interval

To prevent syslog messages or SNMP notifications from being sent too frequently, you can set the
MAC change notification interval to a larger value.

To set the MAC change notification interval:

Step Command

Remarks

Enter system view.

system-view

N/A

Set the MAC change
notification interval.

mac-address information
interval interval-time

The default setting is 1 second.

Configuring the MAC Information queue length

Step Command

Remarks

Enter system view.

system-view

N/A

Configure the MAC
Information queue length.

mac-address information
queue-length value

The default setting is 50.

MAC Information configuration example

Network requirements

Enable MAC Information on interface GigabitEthernet 1/0/1 on Device in

Figure 7

to send MAC

address changes in syslog messages to the log host, Host B, through interface GigabitEthernet
1/0/2.

Содержание FlexNetwork 5130 HI SERIES































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI SERIES

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI SERIES

Бренды по названию

Популярные бренды

HPE FlexNetwork 5130 HI SERIES, Руководство по настройке

Результаты поиска

Содержание FlexNetwork 5130 HI SERIES

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI SERIES

Бренды по названию

Популярные бренды