HPE FlexNetwork 5130 HI SERIES Скачать руководство пользователя страница 38

Страница: 38 / 286

Task Command

Display MAC address table
information.

display mac-address

[

mac

address

[

vlan

vlan-id

] | [ [

dynamic

static

] [

interface interface-type interface-number

] |

blackhole

multiport

] [

vlan

vlan-id

] [

count

] ]

Display the aging timer for dynamic
MAC address entries.

display mac-address aging-time

Display the system or interface MAC
address learning state.

display mac-address mac-learning

[

interface

interface

type

interface

number

]

Display MAC address statistics.

display mac-address statistics

Display the MAC address move
records.

display mac-address mac-move

[

slot

slot-number

]

Figure 6 An example for the display mac-address nickname command

MAC address table configuration example

Network requirements

Host A at MAC address 000f-e235-dc71 is connected to interface GigabitEthernet 1/0/1 of Device
and belongs to VLAN 1.

Host B at MAC address 000f-e235-abcd, which behaved suspiciously on the network, also belongs
to VLAN 1.

Configure the MAC address as follows:

•

To prevent MAC address spoofing, add a static entry for Host A in the MAC address table of
Device.

•

To drop all frames destined for Host B, add a blackhole MAC address entry for the host.

•

Set the aging timer to 500 seconds for dynamic MAC address entries.

Configuration procedure

# Add a static MAC address entry for MAC address 000f-e235-dc71 on GigabitEthernet 1/0/1 that
belongs to VLAN 1.

Содержание FlexNetwork 5130 HI SERIES































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI SERIES

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI SERIES

Бренды по названию

Популярные бренды

HPE FlexNetwork 5130 HI SERIES, Руководство по настройке

Результаты поиска

Содержание FlexNetwork 5130 HI SERIES

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI SERIES

Бренды по названию

Популярные бренды