HPE FlexNetwork 5130 HI SERIES Скачать руководство пользователя страница 236 | Manualshive

Страница: 236 / 286

background image

227

Type Description

•

Power

supply

mode.

•

Whether PSE power supply is supported.

•

Whether PSE power supply is enabled.

•

Whether pair selection can be controlled.

•

Power supply type.

•

Power

source.

•

Power

priority.

•

PD

requested

power.

•

PSE

allocated

power.

Maximum Frame Size

Indicates the supported maximum frame size. It is now the MTU of
the port.

Power Stateful Control

Indicates the power state control configured on the sending port,
including the following:

•

Power supply mode of the PSE/PD.

•

PSE/PD

priority.

•

PSE/PD

power.

NOTE:

The Power Stateful Control TLV is defined in IEEE P802.3at D1.0 and is not supported in later
versions. HPE devices send this type of TLVs only after receiving them.

•

LLDP-MED TLVs
LLDP-MED TLVs provide multiple advanced applications for voice over IP (VoIP), such as
basic configuration, network policy configuration, and address and directory management.
LLDP-MED TLVs provide a cost-effective and easy-to-use solution for deploying voice devices
in Ethernet. LLDP-MED TLVs are shown in

.

Table 22 LLDP-MED TLVs

Type Description

LLDP-MED Capabilities

Allows a network device to advertise the LLDP-MED TLVs that it
supports.

Network Policy

Allows a network device or terminal device to advertise the VLAN ID
of a port, the VLAN type, and the Layer 2 and Layer 3 priorities for
specific applications.

Extended Power-via-MDI

Allows a network device or terminal device to advertise power
supply capability. This TLV is an extension of the Power Via MDI
TLV.

Hardware Revision

Allows a terminal device to advertise its hardware version.

Firmware Revision

Allows a terminal device to advertise its firmware version.

Software Revision

Allows a terminal device to advertise its software version.

Serial Number

Allows a terminal device to advertise its serial number.

Manufacturer Name

Allows a terminal device to advertise its vendor name.

Model Name

Allows a terminal device to advertise its model name.

Asset ID

Allows a terminal device to advertise its asset ID. The typical case is
that the user specifies the asset ID for the endpoint to facilitate
directory management and asset tracking.

Location Identification

Allows a network device to advertise the appropriate location
identifier information for a terminal device to use in the context of

«
...
234
235
236
237
238
...
»

Содержание FlexNetwork 5130 HI SERIES































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FlexNetwork 5130 HI SERIES

Бренд: M2M Страницы: 9

Бренд: PaloAlto Networks Страницы: 3

Бренд: D-Link Страницы: 83

NJ220 - IntelliJack Switch

Бренд: 3Com Страницы: 82

Conel UR5i v2 Libratum

Бренд: B&B Electronics Страницы: 32

Protege PRT-PX16-PCB

Бренд: ICT Страницы: 34

ADSL 2/2+ VPN Firewall Router ADE-4300A/B

Бренд: Planet Страницы: 132

Бренд: Moxa Technologies Страницы: 36

Бренд: Amit Страницы: 75

Бренд: Edimax Страницы: 15

Бренд: Dynamix Страницы: 102

Бренд: Intellinet Страницы: 2

Бренд: l-com Страницы: 2

Бренд: Manson Engineering Industrial Страницы: 10

Бренд: Teltonika Страницы: 12

SmartNode 4634 Series

Бренд: Patton electronics Страницы: 12

Бренд: TP-Link Страницы: 2

Бренд: Pakedge Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды