HPE FlexNetwork 5130 HI SERIES Скачать руководство пользователя страница 235

Страница: 235 / 286

226

Type Description

Remarks

System Description

Specifies the description for the sending device.

System Capabilities

Identifies the primary functions of the sending device and the
enabled primary functions.

Management Address

Specifies the following elements:

•

The management address of the local device.

•

The interface number and object identifier (OID)

associated with the address.

•

IEEE 802.1 organizationally specific TLVs

Table 20 IEEE 802.1 organizationally specific TLVs

Type Description

Port VLAN ID

Specifies the port VLAN identifier (PVID).

Port And Protocol VLAN ID

Indicates whether the device supports protocol VLANs and, if so, what
VLAN IDs these protocols will be associated with.

VLAN Name

Specifies the textual name of any VLAN to which the port belongs.

Protocol Identity

Indicates protocols supported on the port.

DCBX

Data center bridging exchange protocol.

NOTE:

The switch does not support DCBX TLV.

EVB module

Edge Virtual Bridging module, including EVB TLV and CDCP TLV.

NOTE:

The switch does not support EVB TLV.

Link Aggregation

Indicates whether the port supports link aggregation, and if yes, whether link
aggregation is enabled.

Management VID

Management VLAN ID.

VID Usage Digest

VLAN ID usage digest.

ETS Configuration

Enhanced Transmission Selection configuration.

ETS Recommendation

ETS recommendation.

PFC

Priority-based Flow Control.

APP Application

protocol.

NOTE:

HPE devices support only receiving protocol identity TLVs and VID usage digest TLVs.

•

IEEE 802.3 organizationally specific TLVs

Table 21 IEEE 802.3 organizationally specific TLVs

Type Description

MAC/PHY Configuration/Status

Contains the bit-rate and duplex capabilities of the sending port,
support for autonegotiation, enabling status of autonegotiation, and
the current rate and duplex mode.

Power Via MDI

Contains the power supply capabilities of the port:

•

Port class (PSE or PD).

Содержание FlexNetwork 5130 HI SERIES































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI SERIES

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI SERIES

Бренды по названию

Популярные бренды

HPE FlexNetwork 5130 HI SERIES, Руководство по настройке

Результаты поиска

Содержание FlexNetwork 5130 HI SERIES

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI SERIES

Бренды по названию

Популярные бренды