HPE FlexNetwork 5130 HI SERIES Скачать руководство пользователя страница 152

Страница: 152 / 286

143

[DeviceA-vlan5] port gigabitethernet 1/0/5 gigabitethernet 1/0/6

[DeviceA-vlan5] quit

# Configure VLAN 10 as a super VLAN, and associate sub-VLANs 2, 3, and 5 with the super VLAN.

[DeviceA] vlan 10

[DeviceA-vlan10] supervlan

[DeviceA-vlan10] subvlan 2 3 5

[DeviceA-vlan10] quit

[DeviceA] quit

Verifying the configuration

# Display information about super VLAN 10 and its associated sub-VLANs.

<DeviceA> display supervlan

Super VLAN ID: 10

Sub-VLAN ID: 2-3 5

VLAN ID: 10

VLAN type: Static

It is a super VLAN.

Route interface: Configured

Ipv4 address: 10.1.1.1

Ipv4 subnet mask: 255.255.255.0

Description: VLAN 0010

Name: VLAN 0010

Tagged ports: none

Untagged ports: none

VLAN ID: 2

VLAN type: Static

It is a sub VLAN.

Route interface: Configured

Ipv4 address: 10.1.1.1

Ipv4 subnet mask: 255.255.255.0

Description: VLAN 0002

Name: VLAN 0002

Tagged ports: none

Untagged ports:

GigabitEthernet1/0/1 GigabitEthernet1/0/2

VLAN ID: 3

VLAN type: Static

It is a sub VLAN.

Route interface: Configured

Ipv4 address: 10.1.1.1

Ipv4 subnet mask: 255.255.255.0

Description: VLAN 0003

Name: VLAN 0003

Tagged ports: none

Содержание FlexNetwork 5130 HI SERIES































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI SERIES

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI SERIES

Бренды по названию

Популярные бренды

HPE FlexNetwork 5130 HI SERIES, Руководство по настройке

Результаты поиска

Содержание FlexNetwork 5130 HI SERIES

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI SERIES

Бренды по названию

Популярные бренды