HPE FlexNetwork 5130 HI SERIES Скачать руководство пользователя страница 181

Страница: 181 / 286

172

Configure the authorization VLAN for the IP phone on the authentication server. For more
information about authorization VLANs, see

Security Configuration Guide

Displaying and maintaining voice VLANs

Execute

display

commands in any view.

Task Command

Display the voice VLAN state.

display voice-vlan state

Display the OUI addresses that the system supports.

display voice-vlan mac-address

Voice VLAN configuration examples

Automatic voice VLAN assignment mode configuration
example

Network requirements

As shown in

Figure 51

, Device A transmits traffic from IP phones and hosts.

For correct voice traffic transmission, perform the following tasks on Device A:

•

Configure voice VLANs 2 and 3 to transmit voice packets from IP phones A and B, respectively.

•

Configure GigabitEthernet 1/0/1 and GigabitEthernet 1/0/2 to operate in automatic voice VLAN
assignment mode.

•

Add MAC addresses of IP phones A and B to the device for voice packet identification. The
mask of the two MAC addresses is FFFF-FF00-0000.

Figure 51 Network diagram

Configuration procedure

Configure voice VLANs:
# Create VLANs 2 and 3.

<DeviceA> system-view

[DeviceA] vlan 2 to 3

Device A

Device B

GE1/0/1

IP phone B
010-1002
MAC: 0011-2200-0001
Mask: ffff-ff00-0000

0755-2002

GE1/0/2

IP phone A

010-1001

MAC: 0011-1100-0001

Mask: ffff-ff00-0000

Internet

PC A

MAC: 0022-1100-0002

PC B

MAC: 0022-2200-0002

VLAN 3

VLAN 2

Содержание FlexNetwork 5130 HI SERIES































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI SERIES

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI SERIES

Бренды по названию

Популярные бренды

HPE FlexNetwork 5130 HI SERIES, Руководство по настройке

Результаты поиска

Содержание FlexNetwork 5130 HI SERIES

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI SERIES

Бренды по названию

Популярные бренды