HP OMNIBOOK 3000 Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 86

background image

3-20

Troubleshooting and Diagnostics

HP OmniBook 3000

BIOS Setup Utility

The BIOS Setup utility provides access to basic configuration settings. It is independent of the operating
system.

Running the BIOS Setup Utility

1. Close all applications, then shut down Windows and reboot the OmniBook. If necessary, you can

press CTRL+ALT+DEL to reboot.

2. During reboot, when you see “Press <F2> to enter Setup” at the bottom of the screen, press F2 to

start the BIOS Setup utility.

3. The TouchPad or mouse is not active in the BIOS Setup utility. Press the RIGHT and LEFT arrow

keys to move among menus. Press the DOWN and UP arrow keys to move among parameters in a
menu. Press ENTER to change a setting. See the tables below for more information.

4. After you select the options you want, press F10 or use the Exit menu to exit the BIOS Setup utility.

If the settings cause a conflict between devices during reboot, the system prompts you to run BIOS

Setup, and the conflicting settings are marked.

Table 3-6. BIOS Setup Menus and Parameters

Main Menu

Default

System Time

Sets the time using 24-hour format.

System Date

Sets the date using mm/dd/yy format.

Floppy Drive

Shows the floppy drive type.

Hard Disk

Sets the hard disk drive type and various parameters.

Quiet Boot

When disabled, runs power-on self-test and shows summary
during boot.

Disabled

Video Display Device

Sets whether the built-in and external display signals
automatically switch when an external display is detected, or
whether both signals are active. Pressing Fn+F5 temporarily
switches between options.

Auto

System Memory

Shows the system memory size.

Extended Memory

Shows the extended memory size.

System Devices Menu

Default

Parameters marked with * below appear only if the main parameter is Enabled (the values are specified by the
settings below). The list of parameters scrolls if it is longer than the screen.

PS/2 Mouse

Enables the PS/2 TouchPad and external PS/2 mouse, if
present.

Enabled

External Fn Key

Sets whether left-CTRL + left-ALT on an external keyboard is
interpreted as the Fn key.

Enabled

IDE Controller

Enables the primary (hard drive) and secondary (optional CD-
ROM drive) controllers.

Both

FDD Controller

Enables the floppy drive.

Enabled

Serial Port

Sets how the serial port is configured: by the BIOS (specified
settings or automatic) or by a PnP operating system.

Enabled

Base I/O address*

Sets the I/O address and interrupt.

3F8h, IRQ4

Infrared Port

Sets how the infrared port is configured: by the BIOS
(specified settings or automatic) or by a PnP operating
system.

Disabled

Mode

Sets the hardware to support SIR (standard IR), ASK IR
(amplitude shift keyed IR), or FIR (fast-IR) infrared
communications. (Driver installation required.)

SIR

«
...
66
67
68
69
70
...
»

Содержание OMNIBOOK 3000























































































Отзывы:

Нет отзывов

Похожие инструкции для OMNIBOOK 3000

Бренд: ABB Страницы: 14

Бренд: D-Link Страницы: 2

Бренд: Samsung Страницы: 155

Бренд: Samsung Страницы: 154

Бренд: Samsung Страницы: 143

Бренд: Samsung Страницы: 186

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 13

Бренд: Gateway Страницы: 128

Бренд: KARPO Fly Страницы: 13

Бренд: Gateway Страницы: 2

Бренд: T-Tech Страницы: 38

Бренд: 7AMEnfant Страницы: 2

Бренд: IDEAL Страницы: 6

Бренд: IdeaFly Страницы: 3

FireCracker CK17A

Бренд: X10 Страницы: 1

Бренд: Waycon Страницы: 8

Бренд: Wavetronix Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды