manualshive.com logo in svg

HP OMNIBOOK 3000, Руководство по обслуживанию

Поделиться
Скачать
HP OMNIBOOK 3000 Скачать руководство пользователя страница 12

1-6

Product Information

HP OmniBook 3000

System Resources

Below are default values for system resources. To see other, non-default possibilities, use the BIOS
Setup utility (see page 3-20), which lists port and audio device configurations in the System Devices
menu.

The tables in this section show typical resource usage as set up by the OmniBook BIOS. Plug-and-play
operating systems, drivers, and BIOS Setup settings may change some of the entries.

 Table 1-7. System Interrupts

0

System timer

1

Keyboard

2

Cascade IRQ 9

3

Free  (or COM2 infrared port, if enabled)

4

COM1 (serial port)

5

Crystal sound

6

Floppy drive

7

LPT1 (ECP parallel port)

8

Real-time clock

9

Free  (or MIDI, if enabled)

10

Universal Serial Bus (USB) - assigned by Windows 95 driver

11

CardBus controller - assigned by Windows 95 driver

12

TouchPad

13

Numeric data processor

14

Internal hard disk (primary IDE controller)

15

Internal CD-ROM drive (secondary IDE controller)

 Table 1-8. System Memory

00000  - 9FFFF

System memory

A0000  - BFFFF

Video

C0000 - CBFFF

Video BIOS

CC000 - DFFFF

Free (see below)

E0000  - FFFFF

System BIOS

Valid uses for memory addresses CC000-DFFFF:

 • 

Upper memory blocks (UMBs).

 • 

PC card memory windows.

Содержание OMNIBOOK 3000























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды